HackingOnkyo TR-NX509/Boot-message

U-Boot 1.3.3-svn (Nov 29 2010 - 18:05:03)

DRAM:  64 MB
NAND:  NAND Manufacturer id: 20
NAND Device id: 75
NAND device: Manufacturer ID: 0x20, Chip ID: 0x75 (ST Micro NAND 32MiB 3,3V 8-bit)
Bad block table found at page 65504, version 0x01
Bad block table found at page 65472, version 0x01
32 MiB
In:    serial
Out:   serial
Err:   serial
ARM Clock : 400000000 Hz
Hit any key to stop autoboot:  0 

Loading from NAND 32MiB 3,3V 8-bit, offset 0x254000
   Image Name:   Linux-2.6.33-rc4
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1034560 Bytes = 1010.3 kB
   Load Address: c0008000
   Entry Point:  c0008000
Automatic boot of image at addr 0xc0200000 ...
## Booting kernel from Legacy Image at c0200000 ...
   Image Name:   Linux-2.6.33-rc4
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1034560 Bytes = 1010.3 kB
   Load Address: c0008000
   Entry Point:  c0008000
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
init started: BusyBox v1.12.1 (2009-05-25 17:54:13 JST)
starting pid 200, tty '/dev/console': '/etc/init.d/rcS'
/dev/mtdblock9
/dev/mtdblock11
starting pid 227, tty '/dev/console': '/etc/init.d/rc 3'
starting pid 234, tty '/dev/console': '/sbin/getty console'
starting pid 236, tty '/dev/console': '/opt/onkyo/avr/bin/netapp '
starting pid 237, tty '/dev/console': '/opt/onkyo/avr/bin/spid '

Start SPI DAEMON Compiled Date[DATA:Dec 13 2011, TIME:11:00:40]
MontaVista(R) Linux(R) Professional Edition 5.0.0 (0802607)

(none) login: Starting AudioApp(Version:Mid 0.02/08Z02A)
disable_alarm_signal ok!!DA83x version=1.10/11Z13AEA

RAM OPEN OK
DSP83x Version:11Z01A
DSP83x ID:AE6091
Start Netapp Compiled Date[DATA:Dec 13 2011, TIME:11:00:49]
[TimerInitialSeq] called
[TimerInitialSeq (system_timer.cpp 261)]  Send STAT commmand
Start message loop
[MainLoop4eISCP] called
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[SpiService::RawDataCallback] send selector info to audioapp
[SpiService::SendToAudioApp] Sync OK
[NetApp::OnSelectorEvent] called, zone=3, selector=0, setupflat=0
[TimerInitialSeq (system_timer.cpp 283)]  Send DLNG commmand
----> 60 Message resources
****** LangPropertyFileMap ****** TX-NR509
****** LangPropertyFileMap construct OK ******
****** Language setting = ENG ===> /opt/onkyo/avr/etc/pfsInfo/netapp_mongon_eng.properties
*** MessageID Duplicate (270)PA_POP_POPTXT_SIGNIN_CONFIRM_EMAIL
*** MessageID Duplicate (271)PA_POP_POPTXT_SIGNIN_CONFIRM_PASSWORD
*** MessageID Duplicate (342)RH_LIST_TEXT_PLAYLISTS
*** MessageID Duplicate (679)ME_POP_POPTXT_SIGNIN_CONFIRM_PASSWORD
!!!!!!!!!!!!!!!!!!!!!! Filter Copy Success !!!!!!!!!!!!!!!!!!!!!!
DAC 32bit Out Disable!
MODEL_THX_NO!
MODEL_HTIB_NO!
MODEL_AMP_5CH!
FH Plus FW = No!
(Init)Wireless SB No
(Init)Wireless SW No
----> 968 Message resources
[TimerInitialSeq (system_timer.cpp 296)]  Call InitCallback
[NetApp::OnInit] called
[~priority_saver()] set prio = 10
[CoreApp::EnableEthernet] error=No such file or directory
[CoreApp::EnableEthernet] start eth0
[CoreApp::EnableEthernet] start lo
[CoreApp::EmacLinkModified] link up event and restart network!
[CoreApp::RestartNetwork] kill udhcpc and zcip
killall: udhcpc: no process killed
killall: zcip: no process killed
[CoreApp::RestartNetwork] Restart Network
Restarting network interfaces...ifdown: interface lo not configured
ifdown: interface eth0 not configured
ip: RTNETLINK answers: File exists
udhcpc (v1.12.1) started
Sending discover...
Sending select for 10.0.2.137...
Lease of 10.0.2.137 obtained, lease time 43200
killall: zcip: no process killed
deleting routers
route: SIOCDELRT: No such process
adding dns 10.0.0.1
done.
[CoreApp::RestartNetwork] Restart thttpd
killall: thttpd: no process killed
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[SpiService::RawDataCallback] send selector info to audioapp
killall: thttpd_alive_check: no process killed
[NetApp::OnLinkEvent] s=1
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[SpiService::RawDataCallback] send selector info to audioapp
[CoreApp::IPAddrModified] addr=ENET
ND1
D
010000002137
255255000000
010000000001
010000000001
000000000000

[request_manager::notify] request have already been cancelled, key=3
PROC_setup () failed. Status = [0x8000801c]
[NetApp::OnInit] Module init finished
[~priority_saver()] restore prio = 10
[TimerInitialSeq (system_timer.cpp 314)]  Send PROD commmand
[SetProductInfo (system_timer.cpp 94)]  Product ID = AVR0007
[SetProductInfo (system_timer.cpp 96)]  Brand Name = ONK
[SetProductInfo (system_timer.cpp 98)]  Destination = XX
[SetProductInfo (system_timer.cpp 100)]  Product Name = TX-NR509
[SetProductInfo (system_timer.cpp 104)]  Friendly Name = Vaffari
[SetProductInfo (system_timer.cpp 122)]  Software Version = 11Z02ALN
[TimerInitialSeq (system_timer.cpp 348)]  Call Async PostInitCallback
[NetApp::OnPostInit] called
[~priority_saver()] set prio = 10
[NetApp::OnInit] Register TestMode Module
[Register (testmode_module.cpp 32)]  TestMode Module is enabled
[NetApp::OnInit] Try to Register ISCP Module
IscpController::Start()
firmware version is not exist
firmware version is not exist
/opt/onkyo/avr/bin/AmxBcast -e eth0 -b ONKYO -p TX-NR509 -v 1.0.0 -c 60128
Successfully bound in file /tmp/ISCP_CONTROL_SOCK.
listen ok
ecn server thread start port = 60128 
Successfully bound in PORT 60128.
listen ok
thread Ecn listen ok. 
[NetApp::OnInit] Registered ISCP Module
[NetApp::OnInit] Try to Register IPOD Module
[NetApp::OnInit] Registered IPOD Module
[NetApp::OnInit] Try to Register USB Module
Successfully bound in PORT(UDP) 60128.
[NetApp::OnInit] Registered USB Module
[NetApp::OnInit] Try to Register IRadio Module
[NetApp::OnInit] Registered IRadio Module
[NetApp::OnInit] Try to Register Wifi Module
[NetApp::OnInit] Registered Wifi Module
[NetApp::OnPostInit] modloader usb call
+ /etc/init.d/udev start
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[SpiService::RawDataCallback] send selector info to audioapp
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[SpiService::RawDataCallback] send selector info to audioapp
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
+ RET=0
+ echo udev result = 0
udev result = 0
+ [ -e /dev/dsplink ]
+ rm /dev/dsplink
+ [ ! -e /dev/dsplink ]
+ ln -s /tmp/dsplink /dev/dsplink
+ i2c_mod_load
+ modprobe i2c-core
+ modprobe i2c-dev
+ modprobe i2c-davinci
+ usb_mod_load
+ modprobe usbcore
+ modprobe ohci-hcd
+ modprobe musb_hdrc
+ modprobe usb-storage
+ modprobe usbhid
+ fs_mod_load
+ modprobe ntfs
+ modprobe fat
+ modprobe vfat
+ modprobe msdos
+ modprobe nls_utf8
+ modprobe nls_cp932
+ modprobe nls_euc-jp
+ modprobe nls_ascii
+ scsi_mod_load
+ modprobe scsi_mod
+ modprobe sd_mod
+ modprobe sg
+ wlan_mod_load
+ grep DESTINATION
+ cat /etc/pfsInfo/pfsProductInfo.dat
+ awk -F = {print $2}
+ ALP=XX
+ echo Get CountryID from /etc/pfsInfo/pfsProductInfo.dat
Get CountryID from /etc/pfsInfo/pfsProductInfo.dat
+ echo "XX"
"XX"
+ insmod /opt/onkyo/avr/mod/cfg80211.ko wifi_country="XX"
+ insmod /opt/onkyo/avr/mod/mac80211.ko
+ insmod /opt/onkyo/avr/mod/compat.ko
+ insmod /opt/onkyo/avr/mod/compat_firmware_class.ko
+ insmod /opt/onkyo/avr/mod/ath.ko
+ insmod /opt/onkyo/avr/mod/ath9k_hw.ko
+ insmod /opt/onkyo/avr/mod/ath9k_common.ko
+ insmod /opt/onkyo/avr/mod/ath9k_htc.ko
+ mount -t usbfs usbfs /proc/bus/usb
+ [ 0 != 0 ]
+ set +x
[NetApp::OnPostInit] modloader audio call
+ alsa_mod_load
+ modprobe soundcore
+ modprobe snd
+ modprobe snd-timer
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
+ modprobe snd-page-alloc
[SpiService::RawDataCallback] send selector info to audioapp
+ modprobe snd-pcm
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[SpiService::RawDataCallback] send selector info to audioapp
+ modprobe snd-pcm-oss
+ modprobe snd-soc-tlv320aic3x
+ modprobe snd-soc-core
+ modprobe snd-soc-davinci
+ modprobe snd-soc-evm
+ modprobe snd-usb-lib
+ modprobe snd-usb-audio
+ set +x
[NetApp::OnPostInit] modloader audio end
[system_info::GetMachineName] machine name = TX-NR509, size = 8
[system_info::GetVspType] vsp = 1280
[NetApp::OnPostInit] InitializeIRadioView end
[NetApp::OnPostInit] send SelectorEvent selector=3, setupflat=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[NetApp::OnSelectorEvent] called, zone=0, selector=4, setupflat=0
[~priority_saver()] restore prio = 10
[TimerInitialSeq (system_timer.cpp 357)]  Send STAT commmand
[TimerInitialSeq (system_timer.cpp 375)]  Call LateInitCallback
[NetApp::OnLateInit] called
[~priority_saver()] set prio = 10
[NetApp::OnInit] Try to Register DLNA Module
[DlnaInitializeSDK (api/DlnaBaseSystem.c 130)]  initialize random seed
received master command. cmd=60, ms=0
[DlnaInitializeSDK (api/DlnaBaseSystem.c 154)]  Register EventManager.
[DlnaInitializeSDK (api/DlnaBaseSystem.c 234)]  Initialize our mediaspace and mediaspace protocol handlers
[DlnaInitializeSDK (api/DlnaBaseSystem.c 270)]  init media player
[DlnaInitializeSDK (api/DlnaBaseSystem.c 304)]  Announce device and its services to the network
[DlnaInitializeSDK (api/DlnaBaseSystem.c 319)]  Set device description
MANUFACTURER=ONKYO
MANUFACTURL=http://www.onkyo.com
FRIENDLYNAME=Vaffari
MODELNUMBER=TX-NR509
MODELNAME=TX-NR509
MODELURL=http://www.onkyo.com
MODELDESC=AV Receiver
PRESENTURL=http://10.0.2.137/
[DlnaInitializeSDK (api/DlnaBaseSystem.c 323)]  start media renderer
[DlnaInitializeSDK (api/DlnaBaseSystem.c 350)]  finished
[System_Dlna_EnableDMRPlayback (dlna_module.cpp 193)]  called
[DlnaEnableDMRPlayback (api/DlnaBaseSystem.c 745)]  called, status=OFF
[DlnaMSearch (api/DlnaBaseSystem.c 711)]  called
[dlna_cdi_event_callback (api/DlnaServer.c 32)]  called. event=10002
[CDIcallback (Dlna_Base.cpp 104)]  MINUN-PC: Kalle: found, id=xmbms://bb8f3206-a119-4565-ae37-3351859652cb
[Register (dlna_module.cpp 135)]  watch product info
[Register (dlna_module.cpp 145)]  register ip addr event
[Register (dlna_module.cpp 148)]  Call RestartLLTD
sh: you need to specify whom to kill
rm: cannot remove '/var/run/lld2d-eth0.pid': No such file or directory
[Register (dlna_module.cpp 153)]  Finished RestartLLTD
[NetApp::OnInit] Registered DLNA Module
[NetApp::OnSelectorEvent] called, zone=0, selector=4, setupflat=0
[NetApp::OnSelectorEvent] finished
[NetApp::OnSelectorEvent] called, zone=3, selector=0, setupflat=0
[NetApp::OnSelectorEvent] finished
[NetApp::OnInit] Try to Register UPDATE Module
[NetApp::OnInit] Registered UPDATE Module
[NetApp::OnInit] Try to Register PREPRO Module
[dlna_cdi_event_callback (api/DlnaServer.c 32)]  called. event=10002
[CDIcallback (Dlna_Base.cpp 104)]  EyeConnect (Makkari) found, id=xmbms://EAEB-0026B0D73784-01-656C6761746F04
[NetApp::OnInit] Registered PREPRO Module
[NetApp::OnInit] Try to Register Jacket Module
[NetApp::OnInit] Registered Jacket Module
[~priority_saver()] restore prio = 10
[RefreshServerList (Dlna_Base.cpp 310)]  Cache number 2
[RefreshServerList (Dlna_Base.cpp 339)]  xmbms://EAEB-0026B0D73784-01-656C6761746F04 is active and set marks
[RefreshServerList (Dlna_Base.cpp 339)]  xmbms://bb8f3206-a119-4565-ae37-3351859652cb is active and set marks
[RefreshServerList (Dlna_Base.cpp 350)]  Attach Check 2 2 0
[DlnaServerRefreshed (dlna_module.cpp 46)]  svr Number is 2
[NetApp::OnServerUpdated] called
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[NetApp::OnSelectorEvent] finished
[SpiService::RawDataCallback] send selector info to audioapp
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[NetApp::OnSelectorEvent] finished
[SpiService::RawDataCallback] send selector info to audioapp
[avr_system_set_ringio_status] status=0
[NetApp::OnSelectorEvent] called, zone=0, selector=3, setupflat=0
[NetApp::OnSelectorEvent] finished
[SpiService::RawDataCallback] send selector info to audio app